This article will familiarize you with some of the most common and essential audio effects to take your vocal production to the next level. If you are new to home recording, follow these steps to drastically improve the sound of your recorded voice.
In this article you'll learn:
- How to use pitch correction, EQ, de-essing & compression to improve the sonic character of your voice
- How to use reverb as an effect and to give your voice a distinct, ambient space
- How to create solid plug-in & FX chain for your vocal production
Want to add these audio effects to your vocals as you follow along? Add them for free with a Music Production Suite Pro free trial.
Pitch correction/tuning is used in most professional audio recordings to change or improve the intonation of a voice. It can also be used to artificially create harmonies. The amount of pitch correction used on a recording can be a matter of taste, but it’s important for every vocalist to understand the basic functions of pitch correction.
Generally, pitch correction should be added first in your channel strip, as other effects like EQ make it more difficult to perform pitch correction properly.
Pro tip: Melodyne 5 essential adds precise and intuitive pitch adjustment capabilities that are an industry standard in professional recording studios, included with a Music Production Suite Pro free trial.
Now, here is the same vocal with the pitch adjusted to improve intonation:
Vocal with Natural Tuning
Here is the same voice re-tuned at different pitches to create a harmony:
Vocal Harmony Tuning
Vibrato/Pitch Modulation is another parameter used in pitch correction which adjusts the natural pitch variation created as a result of vibrato. A natural voice may alternate pitch slightly above and below the note center during the performance, and adjusting this parameter either increases or decreases the intensity.
If you’re looking for a robotic tuning effect, try removing the vibrato completely. For a more natural turning effect, keep the natural vibrato or increase it.
Here is an example of vibrato removed completely from a vocal recording:
No Vibrato Tuning on Vocals
Here is an example of vibrato being exaggerated and increased on a vocal recording:
Big Vibrato Tuning on Vocals
EQ or equalization is an effect that adjusts the frequency content of a recording. It can be used to remove unwanted or unpleasant frequencies and also be used to sculpt a unique timbre for the voice. Parametric EQs are the most common, and they are set up with low frequencies on the left, and high frequencies on the right (measured in hertz/Hz). The range of frequencies is usually the range of what we as human beings can hear: 20 Hz – 20 kHz.
High Pass Filter
A High Pass Filter is one of the most useful EQ effects to help make your vocal recording sound more professional. A high pass filter “lets highs pass through” or cuts low frequencies. It is most commonly used to remove low frequency problems that come from plosives (recording without a pop filter, creating boomy Ps & Bs) and proximity effect (being too close to the mic while recording).
Here's an example of an extreme case of using a high pass filter to demonstrate the overall shape and sound of a high pass filter. Listen to this voice recorded without a pop filter with extreme plosives in the low frequencies:
Vocals with No EQ
Now listen to the same voice with a HPF at 210 Hz.
Vocals with a High Pass Filter
“Peak & sweep” EQ
“Peak & Sweep” is a technique used to find problematic frequencies when you don’t know precisely what frequency is creating the issue. Parametric EQs have 3 parameters: frequency, gain and Q. The Q value is the bandwidth, or wideness of the range of frequencies being processed.
To find a frequency that you don’t like in your recording, boost the gain of a frequency at an extreme end of the frequency spectrum and give it a narrow Q. Then, slowly start moving the boosted “peak” through the rest of the frequency spectrum until you hear the problem frequency pop out. Then, remove it by reducing the gain.
Here is an example of a voice with a bothersome frequency around 3kHz, identified by peak & sweep:
Vocal EQ with Problematic Frequency
Here is the same voice with the problematic frequency cut/removed.
Vocal EQ Removed
De-essing is a process that reduces the harshness of s’s, or sibilance, in a vocal recording. It is a frequency-dependent compressor, meaning it detects and reduces the volume of a specific frequency or range of frequencies.
Sibilance can be exaggerated when recording with a condenser microphone and can be irritating for listeners, especially on headphones. To get the most out of your de-esser, use it before your compressor.
The threshold is at what level (in decibels) the sibilance has to reach in order to be reduced. The lower the threshold, the more drastically the sibilant frequency will be lowered.
This setting allows you to precisely isolate the frequency range of the sibilance in your recording in order to detect and reduce it.
Here is an example of a vocal without a de-esser and harsh sibilance:
Vocals with No De-essing
Now, here is the same vocal with de-essing added to remove the intensity of the sibilance.
Vocals with De-essing
Compression is a process that unifies the dynamic range of a recording. In other words, it reduces the range between loud and soft dynamics in the vocal, making it more consistent in volume throughout the song.
The threshold is at what level (in decibels) the compressor kicks in and starts compressing. A good trick is to set the threshold near the softest/quietest part of the signal, without going so low that breaths and excess noise are louder than the threshold. Any signal louder than the threshold will be compressed, and anything quieter than the threshold will be left alone.
The ratio is how much a signal gets compressed after going over the threshold. Ratios are usually set up as mathematical ratios, like 5:1 and 3:1. The higher the first number, the more compression is added.
When a signal is compressed, it loses volume by reducing the level of every peak going over the threshold. This process is called gain reduction.
The makeup gain (sometimes called simply gain or output gain) is the output level after the compression process and gain reduction. A good tip is to add back whatever you lost in gain during the compression process.
Here is an example of an uncompressed, dynamic vocal:
Now, here is the same vocal with the threshold set near the quietest word in the phrase, a 5:1 ratio, and makeup gain added back after the compression process.
Reverb is one of the most commonly used vocal effects heard in recorded music. Reverb is the sound of a space, and we experience reverb in our lives every day. To hear the sound of the space you’re in right now, clap a few times to hear how your room responds. Every space has its own ambience, or natural reverb sound.
We can add reverb to our vocals in the DAW to give them a new or different space. Reverb can enhance the timbre and performance of a vocal with a sparkly plate, or make a vocal recorded in a bedroom sound like it was recorded in a large arena.
Reverb time (sometimes referred to as decay or decay time) is the amount of time the reverb effect lasts before trailing off. The longer the reverb time, the more dramatic the reverb and larger the space sounds.
The mix value is how much wet (reverberated) signal is heard. If you are using reverb on a bus, this should always be set to 100%.
Pre-delay is the amount of time (in milliseconds) it takes before the reverb effect actually kicks in. This is an excellent tool to use on vocal reverbs to give time for all of the lyrics and consonants to come through without being overwhelmed by the reverb.
Here is an example of a dry vocal recording with no digital reverb:
Now, here is the same vocal using Neoverb’s “Large Vocal Chamber” with a few adjustments including 82 ms of pre-delay.
Vocals with Reverb
Get started with using audio effects on vocals
Now that you know about these different audio effects, it's time to put them to use. Start a free trial of Music Production Suite Pro and use iZotope's Assistive Audio Technology in Nectar Pro to get to a great starting point on your vocal mix. Nectar Pro's Vocal Assistant analyzes the content of your performance and generates an effects preset form-fitted to the nuances of your singer and your music, including many of these audio effects discussed in this article.